Compact cycloidal reducer evaluation for AGV and AMR steering, lift, and auxiliary rotary mechanisms.
| Evaluation Metric | Typical Range | Buyer Relevance |
|---|---|---|
| Duty cycle | Shift profile and stop-start frequency | Mobile equipment often fails when intermittent loads are treated as steady loads. |
| Environmental exposure | Indoor, dusty, humid, or low-temperature routes | Sealing, lubrication, corrosion protection, and maintenance plans depend on the operating route. |
| Decision Point | Choose When | Verify Before Quote | Next Internal Step |
|---|---|---|---|
| Duty cycle is the first sourcing filter | Best for mobile robot builders balancing torque, durability, and package size. Use this path when duty cycle (Shift profile and stop-start frequency) is more important than starting from a generic gearbox size. | Mobile equipment often fails when intermittent loads are treated as steady loads. Include vehicle module and load profile in the first RFQ packet. | Compare Application Solutions |
| Mechanical interface risk is visible early | Capture acceleration, impact, and stall assumptions. | Shock-load damage: Include impact and stall assumptions in the first RFQ. | Send RFQ Package |
| Sample acceptance must be measurable | Use prototype planning when environmental exposure must be confirmed against buyer-side machine tests. | Fleet maintenance mismatch: Align reducer life, lubrication interval, spare units, and service access with the buyer maintenance model. | Plan Prototype Validation |
| Phase | Engineering / QC Checkpoint | Buyer Output |
|---|---|---|
| Requirement baseline | Vehicle module and load profile; Torque, ratio, speed, and expected duty cycle. Confirm drawing revision, quantity, destination, and timeline in the same packet. | A quote-ready RFQ sheet that separates required performance from preferred options. |
| Engineering fit review | Capture acceleration, impact, and stall assumptions. Review sealing, lubrication, and ambient operating conditions. Record open issues before sample cost and lead time are frozen. | A reducer shortlist and issue log for AGV / AMR Cycloidal Reducer. |
| Prototype or incoming validation | Measure duty cycle and environmental exposure against the agreed method. Include impact and stall assumptions in the first RFQ. | Inspection and test evidence with pass/fail limits, measured values, and revision actions. |
| Batch control and export readiness | Fleet maintenance mismatch: tie the control plan to outgoing inspection, packaging, labeling, and shipment records. | Repeat-order package covering drawing baseline, CTQ records, packaging rules, forecast, and Incoterm. |
Manufacturing Evidence Pack
Use this pack to compare application risk, sample checks, and factory records before treating a cycloidal reducer as a harmonic-drive alternative or a robot-joint candidate.
Scope
Application evidence path
Source
/solutions/agv-amr-cycloidal-reducer
These images support product recognition and envelope review. They are not inspection reports, certificates, or measured test results.
Buyer Review
Tooth profile, pin wheel, eccentric shaft, housing datum, bearing fit, and output interface reviewed as one reducer system.
Artifact to Request
Process photos, CTQ dimension list, approved 2D drawing, CMM or critical-dimension record when available.
Release Status
Requires model-family approval
Buyer Review
Which material route and hardness target apply to this model instead of a generic catalog claim.
Artifact to Request
Material route note, heat-treatment target, hardness inspection field, and sample-lot traceability scope.
Release Status
Do not assume one route for every model
Buyer Review
Backlash method, run-in state, no-load torque, stiffness expectation, noise observation, and smooth low-speed motion.
Artifact to Request
Backlash measurement method, sample acceptance table, no-load torque check, run-in note, and buyer limits.
Release Status
Needs measured sample data
Buyer Review
Envelope, motor pilot, hollow bore, output flange, fastener access, tolerances, and NDA needs before STEP release.
Artifact to Request
Closest reference STEP or PDF, revision note, restricted-drawing release rule, and engineering contact path.
Release Status
Released by engineering check
Buyer Review
Inspection fields, packing method, destination paperwork, batch labeling, sample scope, and repeat-order controls.
Artifact to Request
Outgoing QC checklist, packaging/export record example, batch traceability field, and approved shipping constraints.
Release Status
Align before PO
| Evidence Area | Buyer Review | Artifact to Request | Release Status |
|---|---|---|---|
| Machining route | Tooth profile, pin wheel, eccentric shaft, housing datum, bearing fit, and output interface reviewed as one reducer system. | Process photos, CTQ dimension list, approved 2D drawing, CMM or critical-dimension record when available. | Requires model-family approval |
| Material and heat treatment | Which material route and hardness target apply to this model instead of a generic catalog claim. | Material route note, heat-treatment target, hardness inspection field, and sample-lot traceability scope. | Do not assume one route for every model |
| Backlash and motion check | Backlash method, run-in state, no-load torque, stiffness expectation, noise observation, and smooth low-speed motion. | Backlash measurement method, sample acceptance table, no-load torque check, run-in note, and buyer limits. | Needs measured sample data |
| Drawing and revision control | Envelope, motor pilot, hollow bore, output flange, fastener access, tolerances, and NDA needs before STEP release. | Closest reference STEP or PDF, revision note, restricted-drawing release rule, and engineering contact path. | Released by engineering check |
| Outgoing QC and export pack | Inspection fields, packing method, destination paperwork, batch labeling, sample scope, and repeat-order controls. | Outgoing QC checklist, packaging/export record example, batch traceability field, and approved shipping constraints. | Align before PO |
No certificate or test result should be displayed until approved. Keep the page useful by showing the review path, then attach real evidence during RFQ or after factory approval.
CAD / STEP Data Pack
Use this application package request when your team needs a model file, envelope drawing, or engineering data before committing layout space. We verify the target family, revision, and release constraints first so buyers do not design around the wrong CAD file.
Confirm released model files, closest reference family, and file-release constraints before CAD freeze.
Align motor pilot, output flange, hollow bore, cable route, bolt circle, and axial envelope early.
Request backlash method, run-in note, inspection fields, and sample acceptance data for the selected family.
Inquiry Email
Best for sending NDA terms, drawings, or a specification sheet.
Instant Chat
+8618857971991
Best for quick model availability and file-release checks.
Submit the minimum engineering context needed for model-file screening and revision-safe follow-up.
Application RFQ
Include the machine module, duty profile, ratio, torque, backlash, interface limits, and validation plan so engineering can respond against the real application risk.
Yes. Share load profile, shock assumptions, ambient conditions, and maintenance target.
Steering, lift, docking, and auxiliary rotary modules are typical starting points because torque peaks and package limits are clear.
Program Route
AGV / AMR Cycloidal Reducer defines the use-case risk. The next step is to connect it to the reducer family, drawing request, DFM review, and validation records.
Check reducer architecture, model family, envelope class, and CAD availability before the quote is treated as final.
Review the machine or robot axis context so torque, shock, backlash, stiffness, and validation risk stay tied to real use.
Move from fit review into DFM, sample validation, inspection records, packaging, and repeat-order control.
Use these links when the buyer is ready to send requirements, compare directories, or review sourcing guidance.
Inquiry Email
Include ratio, torque, backlash, interface drawings, quantity plan, and destination terms.
Instant Chat
+8618857971991
Use chat for quick routing; drawings and technical details can move to email.
