Ultra-thin cycloidal gearboxes and flat reduction modules for AGV steering, slim rotary tables, and space-constrained machine axes.
| Metric | Typical Range | Why It Matters |
|---|---|---|
| Axial length | Application-specific ultra-slim profiles | Minimizing axial length allows more compact machine design or larger battery space in AGVs. |
| Moment load | Driven by payload offset and bearing span | Flat reducers often carry off-axis loads; moment data changes bearing and housing selection. |
| Decision Point | Choose When | Verify Before Quote | Next Internal Step |
|---|---|---|---|
| Axial length is the first sourcing filter | Best for equipment designers struggling with axial length constraints in their drive train. Use this path when axial length (Application-specific ultra-slim profiles) is more important than starting from a generic gearbox size. | Minimizing axial length allows more compact machine design or larger battery space in AGVs. Include maximum allowable axial length in the first RFQ packet. | Compare Product Families |
| Mechanical interface risk is visible early | Review axial length vs. moment load capacity tradeoff. | Thermal bottleneck: Ensure continuous duty cycle requirements are shared to evaluate heat dissipation limits. | Send RFQ Package |
| Sample acceptance must be measurable | Use prototype planning when moment load must be confirmed against buyer-side machine tests. | Motor-interface mismatch: Confirm pilot diameter, shaft length, bolt circle, and cable clearance with the selected motor drawing. | Plan Prototype Validation |
| Phase | Engineering / QC Checkpoint | Buyer Output |
|---|---|---|
| Requirement baseline | Maximum allowable axial length; Required moment load and radial load capacity. Confirm drawing revision, quantity, destination, and timeline in the same packet. | A quote-ready RFQ sheet that separates required performance from preferred options. |
| Engineering fit review | Review axial length vs. moment load capacity tradeoff. Define operating temperature limits as heat dissipation is critical in flat designs. Record open issues before sample cost and lead time are frozen. | A reducer shortlist and issue log for Flat Cycloidal Reducer. |
| Prototype or incoming validation | Measure axial length and moment load against the agreed method. Ensure continuous duty cycle requirements are shared to evaluate heat dissipation limits. | Inspection and test evidence with pass/fail limits, measured values, and revision actions. |
| Batch control and export readiness | Motor-interface mismatch: tie the control plan to outgoing inspection, packaging, labeling, and shipment records. | Repeat-order package covering drawing baseline, CTQ records, packaging rules, forecast, and Incoterm. |
Manufacturing Evidence Pack
Use this pack to move a reducer inquiry from catalog interest to buyer-reviewable engineering evidence. The current page can frame the evidence path; approved reports, certificates, and drawings still need to come from the actual model-family review.
Scope
Product evidence path
Source
/products/flat-cycloidal-reducer
These images support product recognition and envelope review. They are not inspection reports, certificates, or measured test results.
Buyer Review
Tooth profile, pin wheel, eccentric shaft, housing datum, bearing fit, and output interface reviewed as one reducer system.
Artifact to Request
Process photos, CTQ dimension list, approved 2D drawing, CMM or critical-dimension record when available.
Release Status
Requires model-family approval
Buyer Review
Which material route and hardness target apply to this model instead of a generic catalog claim.
Artifact to Request
Material route note, heat-treatment target, hardness inspection field, and sample-lot traceability scope.
Release Status
Do not assume one route for every model
Buyer Review
Backlash method, run-in state, no-load torque, stiffness expectation, noise observation, and smooth low-speed motion.
Artifact to Request
Backlash measurement method, sample acceptance table, no-load torque check, run-in note, and buyer limits.
Release Status
Needs measured sample data
Buyer Review
Envelope, motor pilot, hollow bore, output flange, fastener access, tolerances, and NDA needs before STEP release.
Artifact to Request
Closest reference STEP or PDF, revision note, restricted-drawing release rule, and engineering contact path.
Release Status
Released by engineering check
Buyer Review
Inspection fields, packing method, destination paperwork, batch labeling, sample scope, and repeat-order controls.
Artifact to Request
Outgoing QC checklist, packaging/export record example, batch traceability field, and approved shipping constraints.
Release Status
Align before PO
| Evidence Area | Buyer Review | Artifact to Request | Release Status |
|---|---|---|---|
| Machining route | Tooth profile, pin wheel, eccentric shaft, housing datum, bearing fit, and output interface reviewed as one reducer system. | Process photos, CTQ dimension list, approved 2D drawing, CMM or critical-dimension record when available. | Requires model-family approval |
| Material and heat treatment | Which material route and hardness target apply to this model instead of a generic catalog claim. | Material route note, heat-treatment target, hardness inspection field, and sample-lot traceability scope. | Do not assume one route for every model |
| Backlash and motion check | Backlash method, run-in state, no-load torque, stiffness expectation, noise observation, and smooth low-speed motion. | Backlash measurement method, sample acceptance table, no-load torque check, run-in note, and buyer limits. | Needs measured sample data |
| Drawing and revision control | Envelope, motor pilot, hollow bore, output flange, fastener access, tolerances, and NDA needs before STEP release. | Closest reference STEP or PDF, revision note, restricted-drawing release rule, and engineering contact path. | Released by engineering check |
| Outgoing QC and export pack | Inspection fields, packing method, destination paperwork, batch labeling, sample scope, and repeat-order controls. | Outgoing QC checklist, packaging/export record example, batch traceability field, and approved shipping constraints. | Align before PO |
No certificate or test result should be displayed until approved. Keep the page useful by showing the review path, then attach real evidence during RFQ or after factory approval.
CAD / STEP Data Pack
Use this reducer family request when your team needs a model file, envelope drawing, or engineering data before committing layout space. We verify the target family, revision, and release constraints first so buyers do not design around the wrong CAD file.
Confirm released model files, closest reference family, and file-release constraints before CAD freeze.
Align motor pilot, output flange, hollow bore, cable route, bolt circle, and axial envelope early.
Request backlash method, run-in note, inspection fields, and sample acceptance data for the selected family.
Inquiry Email
Best for sending NDA terms, drawings, or a specification sheet.
Instant Chat
+8618857971991
Best for quick model availability and file-release checks.
Submit the minimum engineering context needed for model-file screening and revision-safe follow-up.
Direct RFQ
The form keeps this product family attached to the inquiry so sales engineering can review ratio, torque, backlash, interface, quantity, and delivery assumptions in one thread.
Due to their compact design and limited thermal mass, they are typically better suited for intermittent or medium-speed continuous duty. Please share your speed profile for review.
Send allowable axial length, moment load, torque, speed, duty cycle, motor drawing, and target production volume.
Engineering Route
Flat Cycloidal Reducer should lead to a clear application review, DFM check, prototype evidence plan, and RFQ handoff instead of stopping at a catalog comparison.
Check reducer architecture, model family, envelope class, and CAD availability before the quote is treated as final.
Review the machine or robot axis context so torque, shock, backlash, stiffness, and validation risk stay tied to real use.
Move from fit review into DFM, sample validation, inspection records, packaging, and repeat-order control.
Use these links when the buyer is ready to send requirements, compare directories, or review sourcing guidance.
Inquiry Email
Include ratio, torque, backlash, interface drawings, quantity plan, and destination terms.
Instant Chat
+8618857971991
Use chat for quick routing; drawings and technical details can move to email.
